Any Chinese chainsaw and chinese parts discussion

bogieboy · May 16, 2024

Czed said:
Absolutely I edited it I meant the tsumura light and tough compared to the tsumura lw
I have several powermatch they seem to have improved over the year's
I've got some 90s vintage floppy bastards in the shop the new one's are better.

I have a vintage 90s floppy bastard non light weight 36" oregon on my 661 as of this morning LOL pulled the 404 32" bar off this morning as last night i accidentally put the tip to dirt while doing some cutting.... square ground really doesnt like that.... its now been converted to round ground, as i burned 2 files to half way attempt to put a square edge back on, and mostly failed, potentially due to how hard stihl 404 square skip teeth are...

thedude74 · May 16, 2024

bogieboy said:
New bar/chain i usually set it with no visual droop in the chain, and snug to the point that i can (while tugging pretty hard) JUST (like 1/16" max) pull the drive link out of the channel in the middle of the bar

That's about how I tension them too. Even RS stretches a little on the first tank or two....This NEOTEC chain had zero...first time I've seen that on a new chain. Maybe if I'd been cutting something harder than dead spruce? At any rate. Good chain.

dirter · May 17, 2024

I worked a deal with V-Modest for some overstock chains they have on the Zon. I've used a 36" and a 24" and they worked as well as any of the other Chinese chains, which is pretty good now days. I do get a very very tiny commission on any bought with this code. Edit: the link does work but doesn't show up in the post for some reason. The code is AR5IYOC0WOVZ7 for 50% off
Well crap now I can't get the code to work. Never mind, I'll try to get it figured out.
www.amazon.com/promocode/AR5IYOC0WOVZ7

Amazon.com Page Not Found

Czed · May 17, 2024

dirter said:
I worked a deal with V-Modest for some overstock chains they have on the Zon. I've used a 36" and a 24" and they worked as well as any of the other Chinese chains, which is pretty good now days. I do get a very very tiny commission on any bought with this code. Edit: the link does work but doesn't show up in the post for some reason. The code is AR5IYOC0WOVZ7 for 50% off
Well crap now I can't get the code to work. Never mind, I'll try to get it figured out.
www.amazon.com/promocode/AR5IYOC0WOVZ7

Amazon.com Page Not Found

Thanks
I ordered a 3 pack of 84dl to try out it's 20.50 shipped
I tried using your code but it automatically took 50% off before i could add it.

dirter · May 17, 2024

Czed said:
Thanks
I ordered a 3 pack of 84dl to try out it's 20.50 shipped
I tried using your code but it automatically took 50% off before i could add it.

Ah, good. I don't really buy stuff on Amazon so I'm not real up to speed with it. I just ask my wife to get whatever it is and it shows up in a day or two. She's kind of good that way

dirter · May 17, 2024

Czed said:
Thanks
I ordered a 3 pack of 84dl to try out it's 20.50 shipped
I tried using your code but it automatically took 50% off before i could add it.

I'm slowly figuring some of this out. The promo code is actually 50A9P8JW.

Czed · May 17, 2024

thedude74 said:
What are your thoughts on power match vs Tsumura durability wise. I'm in need of a 36" D009 for mostly milling purposes. The Oregon is about $100... Tsumura about $150...Is it worth the difference in cost?

Tsumura hands down my favorite
I'm still running my 80s vintage total super bars and tipton Tsumura manufactured bar's
They always far outlasted Oregon in my use
Windsor and cannon made fine bars also
Oregon has greatly improved in the past 10 year's I'm running at least 6 versacut aluminum cores and a 4 solid bars.
I wouldn't hesitate to buy Oregon now
But honestly I'd get a pile of the china bars because I'd bend or damage a bar more often than wear one out.

Czed · May 17, 2024

I probably have 25-35 Tsumura bar's floating around my shop.

thedude74 · May 17, 2024

I like Tsumura too. Sometime back around when I joined OPE and read the reviews I bought a few. They were cheap back then! 20" were $25...24" were $29.

thedude74 · May 17, 2024

@dirter That is a good deal! $14.92 for three 20" 3/8 .050 Full chisel.

thedude74 · May 17, 2024

Finally got a shipping date on the 28" light bars....had to talk to Amazon customer service. Should be here in a couple weeks

thedude74 · May 17, 2024

$189 after discount for an MS380 clone...free shipping pho.....or $199 with 24" bar

ammoaddict · May 17, 2024

So I fired up the nh895 after I looked it over a bit. Started up in 7 pulls, idled good. Reved it up a bit, just didn't sound like it was getting to full speed. Found out the throttle is not opening all the way with the trigger fully pressed. It had a stop it's supposed to hit bit it only gets about 3/4 of the way there. I took a picture it fully pressed. I sent neotec an email but haven't heard back yet. Any ideas how to fix this if they don't do anything about it?

Czed · May 17, 2024

ammoaddict said:
So I fired up the nh895 after I looked it over a bit. Started up in 7 pulls, idled good. Reved it up a bit, just didn't sound like it was getting to full speed. Found out the throttle is not opening all the way with the trigger fully pressed. It had a stop it's supposed to hit bit it only gets about 3/4 of the way there. I took a picture it fully pressed. I sent neotec an email but haven't heard back yet. Any ideas how to fix this if they don't do anything about it?View attachment 419898

Make sure the cable is in it's recess on the handle.

ammoaddict · May 17, 2024

Czed said:
Make sure the cable is in it's recess on the handle.

I took the side covers off the handle and it's in the holder. Maybe the cable is too long? I've never messed with throttle cables, only linkages. I don't really know how to fix it.

Czed · May 17, 2024

ammoaddict said:
I took the side covers off the handle and it's in the holder. Maybe the cable is too long? I've never messed with throttle cables, only linkages. I don't really know how to fix it.

If the cable sleeve isn't in the proper recess for the cable to travel
Sometimes they won't fully open.
I unhook the upper cable and use a hemostat to make sure the bottom is seated correctly
It may be that simple.

ammoaddict · May 17, 2024

Czed said:
If the cable sleeve isn't in the proper recess for the cable to travel
Sometimes they won't fully open.
I unhook the upper cable and use a hemostat to make sure the bottom is seated correctly
It may be that simple.

Ok, I'll wait to see if neotec replies. Is the 395 cable hooked up just like a 372 cable? I built a 372 kit once but the cable was already in the handle, I just had to hook it to the carb. It worked fine.

thedude74 · May 17, 2024

ammoaddict said:
Ok, I'll wait to see if neotec replies. Is the 395 cable hooked up just like a 372 cable? I built a 372 kit once but the cable was already in the handle, I just had to hook it to the carb. It worked fine.

For what its worth I didn't have any luck with emailing them on the website(might have replied to spam folder???)
Messaged Elaine on Facebook and she responded in a matter of minutes. Super nice lady.

This is her

dirter · May 17, 2024

ammoaddict said:
So I fired up the nh895 after I looked it over a bit. Started up in 7 pulls, idled good. Reved it up a bit, just didn't sound like it was getting to full speed. Found out the throttle is not opening all the way with the trigger fully pressed. It had a stop it's supposed to hit bit it only gets about 3/4 of the way there. I took a picture it fully pressed. I sent neotec an email but haven't heard back yet. Any ideas how to fix this if they don't do anything about it?

I’ve had a few 372s like that too. My fix is to strip a small length of insulation from a 14ga wire, split it, then pull the outer cable cover out of that bracket on the carb & put the insulation on the cable and up into the bracket. Refit the cable and you’re good to go. Essentially it’s just lengthening the outer cover like you would adjusting the old dirt bike brake cables.

Fleethirte · May 17, 2024

thedude74 said:
With 10% off comes to $25 shipped for three 72dl .050 3/8 full chiselView attachment 419572

i got some, looks just like the dukes chain but without the duke label on them

Any Chinese chainsaw and chinese parts discussion

Well-Known OPE Member

Bonafide & Stuff !!!

Super OPE Member

Aluminium Member

Super OPE Member

Super OPE Member

Aluminium Member

Aluminium Member

Bonafide & Stuff !!!

Bonafide & Stuff !!!

Bonafide & Stuff !!!

Bonafide & Stuff !!!

Pinnacle OPE Member

Aluminium Member

Pinnacle OPE Member

Aluminium Member

Pinnacle OPE Member

Bonafide & Stuff !!!

Super OPE Member

Super OPE Member

Similar threads